HOME  |   COMPANY  |   BLOG  |   CONTACT US  |   CART



VIEW MANUFACTURER
Sthenic Energy Conservation Product This Item Is Drop Shipped From The Manufacturer Free Shipping
SHARE THIS PAGE
Bookmark and Share
Waterfall/Landscape Lighting Control Kit - Outdoor by Sthenic
  • No Wires! No Batteries!
  • Place switch up to 150 feet from receiver
  • Surface mount switch with screw in or adhesive
  • Finish your landscape wiring project in 1/3 of the time with 1/3 of the wiring
  • Incorporates EnOcean wireless technology
Outdoor water features or landscape lighting can easily be controlled with an on/off relay switch placed anywhere that is convenient for you.Simply wire the receiver to your outdoor electrical feature and mount the switch where it is easily accessible. The press of the switch powers the radio wave that tells the receiver to turn the device on. Optionally add additional receivers to turn fountains and lights on at the same time.

Also, great for turning exterior lighting off from an interior location without an existing switch.

Kit includes:
  • One: Single Rock Decorator Switch (White)
  • One: 5-Wire In Relay Receiver

Receiver

Switch

Item No.

Vendor No.

Description

MSRP

Our Price

QTY

 

20240010

E3K-S11WH

Waterfall/Landscape Lighting Control Kit - Outdoor FREE SHIPPING

$219.90

$160.49



Wireless Light Switch
Range
50-150 feet (typical)
Frequency
315 MHz
Power Supply
Self-generated when switch is pressed
Buttons
2 Buttons (1 rocker)
Dimensions
2.75(W) x 4.5(H) x 0.62(D) inches
Operating Temperature
-13 to +149 degrees F (- 25 to + 65 degrees C)
Radio Certifications
FCC (U.S.), IC (Canada)
Addressing
Factory set unique ID (1 of 4 billion)

5-Wire Relay Receiver
Range
50-150 feet (typical)
Frequency
315 MHz
Power Supply
24 VAC
50/60 Hz
Relay Output
277 VAC, Max
Max Loads / Contact Ratings
Tungsten (Incandescent) N.O. Contacts / N.C. Contacts
1500 W @ 120 VAC / 500 W @ 120 VAC
3000 W @ 240 VAC / 1000 W @ 240 VAC
3400 W @ 277 VAC / 1100 W @ 277 VAC
Fluorescent Ballast
8 A (N.O. Contacts)
General Duty
16 A (N.O. Contacts), 5 A (N.C. Contacts)
A300 Pilot Duty
72 VA @ 24 VAC, 360 VA @ 120 VAC, 720 VA @ 240 VAC, 830 VA @ 277 VAC
Motor Load
60 LRA, 10 FLA, 1/2 HP @ 120 VAC, 1HP @ 240 VAC, 1HP @ 277 VAC
Output Channels
1 FORM C Relay COM, N.O., N.C.
Memory
Stores up to 30 switch IDs
Dimensions
2.11 x 1.73 x 1.09 inches (54 x 44 x 28 mm)
Operating Temperature
+14 to +122 degrees F (-10 to +50 degrees C)
Storage Temperature
-4 to +176 degrees F (-20 to +80 degrees C)
Radio Certification:
FCC (U.S.): SZV-TCM2XXC
IC (Canada): 5713A-TCM2XXC
Safety Approval:
ETL (U.S.): UL244A, UL2043
ETL(Canada): CSAc22.2#14-05
Plenum Rating
UL2043
Installation

Each package is preprogrammed to work with your switch(es) and receiver(s). If you purchased additional receivers or switches you will have to program them to communicate with each other. This is easy to accomplish and instructions will be included with your order. Always follow local electrical codes when installing this device. If you are unsure about any portion of these instructions, please contact a qualified electrician.

The Relay Receiver is wired between the light fixture and the power source.
  1. WARNING: To avoid fire, shock, or death, TURN OFF POWER at circuit breaker or fuse and verify that it is OFF before installation begins. Make sure that it remains OFF until installation is complete.
  2. For in-wall mounting, a wiring box must be used and be rated for exterior use. For best performance do not mount the receivers close to the floor or near wall niches. Do not mount the receiver into a metal housing.
  3. Prepare wires: Pull off pre-cut insulation from Relay Receiver leads. Verify wires are not frayed; cut if necessary removing 5/8" (1.6 cm) of insulation from each wire.
  4. Connect wires. Screw wire nuts on clockwise making sure no bare conductors show below the wire connectors. Secure each connection with electrical tape.
  5. Position and stow all wires in the junction box, then restore power.
  6. Test the range of the wireless light switch before mounting.
  7. Wireless light switches can be mounted in a standard switch box or surface mounted using screws or adhesive.



Approved by: to meet UL Standards.




Frequently Asked Questions

Why is my receiver independently turning ON and OFF?

  • This can occur when an unintended transmitter is activated within the receiver range when the receiver is in Learn Mode.
  • Clear all transmitters in the receiver and reprogram the receiver

My receiver is not responding to my transmitter command, why?

  • Move the switch closer to the receiver. If the system works at closer distance, the transmitter was installed outside the reception range, or there was radio signal interference. Repeaters that extend the coverage range are available; please contact your dealer.
  • Mount the switch or the receiver at a better location.

What is the range of my wireless connectors?

  • Masonry 65 ft. (20m), through 3 walls max.
  • Reinforced concrete 32 ft. (10m), through 1 wall / ceiling max.
  • Wood walls / drywalls 98 ft. (30m), through 5 walls max.

How can I reprogram my devices?

  • Contact customer service at (877)433-7763.




Adobe Acrobat Reader
  GED On FaceBook GED On Twitter Green Express Direct on LinkedIn 

Phone:
(877)GED-PRODUCTS

eMail:
info@greenexpressdirect.com

FAX:
(702)651-1303



SITE MAP

Support Pages
Product Pages
Social Networks
Energy
Green Express Direct