HOME  |   COMPANY  |   BLOG  |   CONTACT US  |   CART



VIEW MANUFACTURER
Sthenic Energy Conservation Product This Item Is Drop Shipped From The Manufacturer
SHARE THIS PAGE
Bookmark and Share
Wireless Daylighting Kit (ON/OFF) by Sthenic
  • Can generate LEED credits
  • Automatically turn lights off in daylight
  • Save up to 60% on energy use
  • No wires to run - save money on installation
  • Incorporates EnOcean wireless technology
The Daylighting Kit includes a wireless, battery-free light sensor that communicates with the relays wired to the lighting system to turn lights on or off based on the quantity of natural lighting. Save up to 60 percent of the rooms lighting costs. This system may help buildings qualify for LEED credits and comply with International Green Construction Code Standard 189.1. When fully charged the sensor can work in total darkness for up to three days.

Kit includes:
  • One: Single Rock Decorator Switch (White)
  • One: Light Sensor
  • One: 3-Wire In Relay Receiver

Light Sensor

Switch

3-Wire Receiver

Item No.

Vendor No.

Description

MSRP

Our Price

QTY

 

20240013

E3K-UWH

Wireless Daylighting Kit (ON/OFF) FREE SHIPPING

$449.85

$319.49



Wireless Light Switch
Range
50-150 feet (typical)
Frequency
315 MHz
Power Supply
Self-generated when switch is pressed
Buttons
2 Buttons (1 rocker)
Dimensions
2.75(W) x 4.5(H) x 0.62(D) inches
Operating Temperature
-13° to +149°F (- 25° to + 65°C)
Radio Certifications
FCC (U.S.), IC (Canada)
Addressing
Factory set unique ID (1 of 4 billion)

Wireless Battery-Free Light Sensor
Range
20-150 feet (typical)
Frequency
315 MHz
Internal Solar Cells
Requires 3 hours of 200 lux per day for continuous operation
Internal Battery (optional)
1/2 AA, 3.6 V. Lithium
External Solar Cell (optional)
7 VDC max.
External Power (optional)
8-30 VAC or VDC
Contact Input (optional)
Optional external dry-contact
Operating Temperature
-13° to +140°F (-25° to +60°C)
Storage Temperature
-40° to +140°F (-40° to +60°C)
Illuminance Range
0 - 1024 lux
Illuminance Accuracy
+/- 10%
Dimensions
3.5 x 3.7 x 1.1 inches (89 x 94 x 28 mm)
Radio Certification
FCC (United States): Pending

Built-In Relay Receiver
Range
50-150 feet (typical)
Frequency
315 MHz
Relay Output
120 V AC
Max Loads / Contact Ratings
Tungsten / Incandescent
500 W
Fluorescent Ballast
3 A
General Duty
6 A
A300 Pilot Duty
120 VA
Power Supply
120 VAC
50/60 Hz
Output Channels
1 FORM A Relay
Memory
Stores up to 30 switch IDs
Dimensions
2.11" x 1.73" x 1.09"
Operating Temperature
+14° to +122°F
Storage Temperature
-4° to +176°F
Radio Certification:
FCC (U.S.): SZV-TCM2XXC
IC (Canada): 5713A-TCM2XXC
Safety Approval:
ETL (U.S.): UL244A, UL2043
ETL(Canada): CSAc22.2#14-05
Plenum Rating
UL2034
Installation

Each package is preprogrammed to work with your switch(es), receiver(s) and sensors. If you purchased additional receivers or switches you will have to program them to communicate with each other. This is easy to accomplish and instructions will be included with your order. Always follow local electrical codes when installing this device. If you are unsure about any portion of these instructions, please contact a qualified electrician.

The Relay Receiver is wired between the light fixture and the power source.
  1. WARNING: To avoid fire, shock, or death, TURN OFF POWER at circuit breaker or fuse and verify that it is OFF before installation begins. Make sure that it remains OFF until installation is complete.
  2. For in-wall mounting, a wiring box must be used. For best performance do not mount the receivers close to the floor or near wall niches. Do not mount the receiver into a metal housing.
  3. Prepare wires: Pull off pre-cut insulation from Relay Receiver leads. Verify wires are not frayed; cut if necessary removing 5/8" (1.6 cm) of insulation from each wire.
  4. Connect wires. Screw wire nuts on clockwise making sure no bare conductors show below the wire connectors. Secure each connection with electrical tape.
  5. Position and stow all wires in the junction box, then restore power.
  6. Mount Sensor in an appropriate location for full operation.
  7. Test the range of the wireless light switch before mounting.
  8. Wireless light switches can be mounted in a standard switch box or surface mounted using screws or adhesive.



Approved by: to meet UL Standards.




Frequently Asked Questions

Why is my receiver independently turning ON and OFF?

  • This can occur when an unintended transmitter is activated within the receiver range when the receiver is in Learn Mode.
  • Clear all transmitters in the receiver and reprogram the receiver

My receiver is not responding to my transmitter command, why?

  • Move the switch closer to the receiver. If the system works at closer distance, the transmitter was installed outside the reception range, or there was radio signal interference. Repeaters that extend the coverage range are available; please contact your dealer.
  • Mount the switch or the receiver at a better location.

What is the range of my wireless connectors?

  • Masonry 65 ft. (20m), through 3 walls max.
  • Reinforced concrete 32 ft. (10m), through 1 wall / ceiling max.
  • Wood walls / drywalls 98 ft. (30m), through 5 walls max.

How can I reprogram my devices?

  • Contact customer service at (877)433-7763.




Adobe Acrobat Reader
  GED On FaceBook GED On Twitter Green Express Direct on LinkedIn 

Phone:
(877)GED-PRODUCTS

eMail:
info@greenexpressdirect.com

FAX:
(702)651-1303



SITE MAP

Support Pages
Product Pages
Social Networks
Energy
Green Express Direct